Handling Operator Tasks

This section provides instructions for handling existing operator tasks in Desigo CC Flex client, for example to start, cancel, or revert a task.
For instructions on how to create or modify an operator task, see Setting Up Operator Tasks.

 

Prerequisites

Check the List of Operator Tasks

You can monitor the currently configured operator tasks in the Tasks tab.

  1. Select the Tasks tab.
  2. The Tasks tab lists all the existing operator tasks, each with its status and other information. For full details about the meaning of task statuses, see Tasks List and Statuses.
  3. Check for tasks that require attention, these are highlighted in red. In particular:
    • Expired: The task ended (due date reached) but without the expected outcomes of its commands. See Handle an expired task.
  4. Tasks available for starting are those in the following statuses:
  5. To help you find tasks in the list you can sort by a specific column: Click a header to sort by that column. An arrow indicates the sort order. Click the same header again to switch between ascending / descending sort order.

Start an Operator Task

  1. A task can be started if its status is Idle or Failed.
    NOTE: For full details about the meaning of task statuses, see Tasks List and Statuses.
  1. Select the Tasks tab.
  2. In the Tasks list, select the desired task.
  3. In the task details pane, click Start.
    • If the status changes to Idle, the task could not be executed because you do not have authorization rights to execute its commands.
    • If a message indicates to you that the task requires a manual revert as soon as it completes, click Yes to run the task with manual revert, or click No to not execute the task.
    • If a message indicates you lack the authorization for automatic revert on a task, click Yes to run the task anyway with forced manual revert, or click No to not execute the task.
  4. If the Note dialog displays, enter your comment, and click OK.
    For example, alarms disabled on the third floor from 3pm to 5pm because of a check on the fire system.
  5. After clicking Start, a typical sequence of statuses in a normal task execution may include:
    • Deferred: The task is waiting to begin after the delay configured in Start Date.
    • Executing commands: The commands in the task are being executed.
    • Running or Running with exceptions: All or some of the commands were issued successfully. The task remains in this status until the Due date is reached.
    • Ready to be closed. The Due date was reached and the conditions resulting from execution of the task commands were met.
  6. An event is generated in Event List if the tasks status is Deferred, Running, or Ready to be closed (see Operator Tasks Reminders in Event List).
    In each case, the event is automatically cleared from Event List when the task status changes.
  7. When the task due date is reached and the Revert Mode is set to (see Revert an Operator Task):
  8. Automatic: The commanded objects are set back to the configured state.
  9. Manual: Click the Revert to execute the revert commands.

NOTE 1: When the task status is Deferred or Executing commands, the Due date that is displayed is only an estimated value that might change dynamically until the task status becomes Running.

NOTE 2: If there was a problem executing the task, the relevant event is generated in Event List (see Operator Tasks Reminders in Event List), and one of the following statuses will result:

In the Targets expander, the Result column displays the details of command execution on each target object. For details, see Command Result Icons.

 

Revert an Operator Task

Reverting a task sets all the commanded objects back to their configured state. For example, if an operator task sets a fire panel to Test Mode, reverting will set the panel back to Normal Mode.

  1. The task has revert actions (manual or automatic).
  2. The task status is one of the following:
    - Running (or Running with exceptions)
    - Failed
    - Expired
  1. Select the Tasks tab.
  2. In the Tasks tab, select the task that you want to revert.
  3. Click Revert and confirm.
  4. If the Note dialog box displays, enter your comment, and click OK.
  5. After clicking Revert, the status changes to:
    • Reverting Commands: commands are being executed to set the properties back to their original state.
  6. The system checks the conditions resulting from execution of the revert commands. Based on the outcome of this, the task status becomes:

 

Close an Operator Task

Closing a task enables you to subsequently delete it or duplicate it to run it again.

  1. You can close a task when its status is:
    - Running (or Running with exceptions)
    - Failed
    - Expired
    - Ready to be closed
  1. Select the Tasks tab.
  2. In the Tasks list, select the task that you want to close.
  3. Click Close.
  4. If the Note dialog box displays, enter your comment, and click OK.
  1. The task status becomes Closed.
    It is now possible to delete or duplicate the task.

 

Handle an Expired Task

When the task status is Expired it means that the task ended (due date reached) without the expected outcomes of its commands being achieved.

  1. Select the Tasks tabs.
  2. In the Tasks list, select the expired task.
  3. (Optional) In the Targets expander, check the Result column for details about the command execution on each target object.
  4. You can try again to send the commands in one of the following ways:
    • Manually satisfy the conditions by executing the commands from the Properties section in the right-hand pane for the target.
  5. Otherwise, click Close. (Consequently, the task status becomes Closed).

 

Abort an Operator Task

Aborting interrupts a previously started task and stops the commands from being executed.

  1. You can abort a task when its status is:
    - Deferred
    - Executing commands
    - Reverting commands
  1. Select the Tasks tab.
  2. In the Tasks list, select the task that you want to interrupt.
  3. If the Note dialog box displays, enter your comment, and click OK.
  4. Click Abort and confirm.
  1. The task status becomes Failed.

View the Notes or Details from Previous Execution

  1. In System tab > System Browser, select Log Viewer
  2. In the Select Columns dialog box, set and sort the appropriate filters to view operator tasks notes and details. For example:
    • Date/Time
      (Date and time when an action occurred in the system)
    • Record Type
      (Activity or Event)
    • Source Description
      (Source of the action. In this case, Operator Tasks.)
    • Source Property
      (For example, ExpiredTasks)
    • Action Details
      (Description of the task action executed. For example, Task closed.:Suppress Alarms.)
    • Comment
      (Any comment entered when performing certain operations on tasks.)
      NOTE: The operator tasks notes can be viewed in the Notes expander of the Tasks tab: this contains a maximum of ten notes. You can view more notes in the Comment column that displays all the tasks notes retrieved from the database. The history log clearly indicates if a revert action will be executed automatically (using the username of the operator who started the task). For more information, see Tasks Notes and Validation.
    • Action result
      (For example, Succeeded)
  3. Click OK.
  4. Click Refresh to retrieve the latest data.
  1. The Details Log tab refreshes to display the latest data.